30 Amp Permanent ELCI/GFPD
Industrial Grade - Industrial Tough

30 Amp Permanent ELCI/GFPD

• Ground Fault Protection Device (GFPD)
• Elevated trip levels to reduce nuisances tripping
• 10mA, 20mA, 30mA Trip settings
• Industrial design for rough service application
• NEMA 4X and 6P wet location rated
• CSA agency listed

  • Class I Ground Fault Protection Device (GFPD)
  • Elevated trip levels to reduce nuisances tripping
  • 10mA, 20mA, 30mA Trip settings
  • Industrial design for rough service application
  • Largest 30 Amp switching contacts in the industry - (high reliability)
  • Dual indication lights displaying power and fault status
  • Open neutral protection (on applicable models only)
  • Grounded neutral protection (on applicable models only)
  • 1Ø & 3Ø CSA, cCSA, cCSAus listed to UL 1053 and CSA C22.2 No. 144-M91
  • Class I GFPD exception 277 VAC (non-Listed) Enclosure is Chemical and U.V. resistant
  • NEMA 4x and 6P wet location rated for indoor/outdoor applications
  • Double insulated user interface for added safety
  • Available in Automatic or Manual (safe start) reset models
  • Surge protection available as a factory custom
  • Surface mountable (4 location) Panel mountable (2 blind cover holes)
  • Flying leads for electrical field

Industrial Grade Ground Fault Protection Device (GFPD) is ideal for both new and existing circuit installations. This GFPD has a unique design that offers the flexibility of splicing-in the protection of a GFPD anywhere within the length of a circuit run. This convenience allows the installer to place this GFPD at an accessible location for the end user. Unlike breaker style GFPDs which have limitations of circuit length from the service panel: the Permanent Series GFPD is installed at the point of use and thus has no restrictions to circuit length by definition. The Permanent Series GFPD can be integrated directly into a circuit or paired in tandem with an approved receptacle and enclosure. All units have 18” splicing lead wires, a ¾” NPT fitting that can connect to ¾” PVC, EMT, Burial and Flexible conduits. In addition, the unit can be installed as a panel mount. Multiple fault output options are available. All units are available in an Automatic or Manual (safe start) reset type. Note ground wire is connected externally to GFPD device and does not enter the GFPD housing. All units are MADE IN THE USA and tested by CSA to UL1053 and CSA 22.2 No. 144-M91 standards.

  • Type: Class I
  • Voltage: 120VAC, 208VAC, 240VAC, 277VAC, 120/240VAC, 120/208VAC Dual Voltage, 120/208VAC 3Ø, 240VAC 3Ø, 208VAC 3Ø
  • Operating Voltage Range: 85% TO 110% of rated voltage
  • Current: Up to 30 Amps
  • Frequency: 50/60 Hz
  • Trip level: 10, 20, 30 mA Trip Levels
  • Phase: Single, Dual Voltage, and 3Ø (WYE and Delta)
  • Response Time: 25 mS max @ 500 Ohm Fault
  • Operating Temperature: -35°C to 66°C
  • Let Go Voltage: 60% rated voltage
  • Reset Type: Automatic or Manual (safe start)
  • Open Neutral Protection: Opens upon loss of neutral (only on applicable models)
  • Grounded Neutral Protection: Trips if ground and neutral touch at load side (only on applicable models)
  • Enclosure: NEMA 4X and 6P wet location rated; high impact withstand
  • Switch Interface: Double insulated
  • Latching Mechanism: Electro-magnetic
  • Agency Approval: CSA, cCSA, cCSAus; CSA-C22.2 No. 144-M91 - UL 1053 (277 VAC non Listed)