30 Amp Portable ELCI/GFPD
Industrial Grade - Industrial Tough

30 Amp Portable ELCI/GFPD

• Ground Fault Protection Device (GFPD)
• Elevated trip levels to reduce nuisances tripping
• 10mA, 20mA, 30mA Trip settings
• Industrial design for rough service application
• NEMA 4X and 6P wet location rated
• CSA agency listed

  • Class I Ground Fault Protection Device (GFPD)
  • Elevated trip levels to reduce nuisances tripping
  • 10mA, 20mA, 30mA Trip settings
  • Industrial design for rough service application
  • Largest 30 Amp switching contacts in the industry - (high reliability)
  • Dual indication lights displaying power and fault status
  • Open neutral protection (on applicable models only)
  • Grounded neutral protection (on applicable models only)
  • 1Ø & 3Ø CSA, cCSA, cCSAus listed to UL 1053 and CSA C22.2 No. 144-M91 Class I GFPD exception 277 VAC (non-Listed)
  • Enclosure is Chemical and U.V. resistant
  • NEMA 4x and 6P wet location rated for indoor/outdoor applications
  • Double insulated user interface for added safety
  • Available in Automatic or Manual (safe start) reset models

The LineGard 30 Amp Portable Series Ground Fault Protection Device comes factory standard with flying leads (no plug or connector) for field configuring and can be constructed into stand-alone cord sets or equipment integrated power supply cords. Exceptions are SKUs with molded twistlock devices. The LineGard 30 Amp Portable Series is industrially designed with impact resistant materials that withstand Chemical and Ultraviolet light degradation and is suitable for both indoor and outdoor applications. The Portable Series is geared for wet location use as this device achieves both NEMA 4X and 6P ratings. The device also includes double insulated and recessed interface switches for additional safety while preventing accidental switching during rough handling. In addition, the electrical contacts of this device are electro-magnetically latched so unit will not delatch under rough use or service. For user convenience, the 30 Amp Portable Series incorporates two LEDs for power and fault status. The product is available in both Automatic and Manual (safe start) reset types. All units are MADE IN THE USA and tested by CSA to UL1053 and CSA 22.2 No. 144-M91 standards. With acceptable volume, North Shore Safety will entertain custom assemblies that are not suitably supported by our standard SKU offering. In addition, all assemblies can be factory integrated with NEMA or IEC wiring devices (watertight and non-watertight) or custom terminations for convenient end-use or installation.

  • Type: Class I
  • Voltage: 120 VAC, 208 VAC, 240 VAC, 277 VAC (277 Non-Listed), 120/240 VAC, 120/208 Dual Voltage,
  • 120/208 VAC 3Ø, 240 VAC 3Ø, 208 VAC 3Ø
  • Operating Voltage Range: 85% up to 110% of rated voltage
  • Current: Up to 30 Amps
  • Frequency: 50/60 Hz,
  • Trip Level: 10, 20, 30 mA Trip Levels
  • Phase: Single, Dual Voltage, and 3Ø (WYE and Delta)
  • Response Time: 25 mS max @ 500 Ohm fault
  • Operating Temperature: -35°C to 66°C
  • Let Go Voltage: 60% rated voltage
  • Reset Type: Automatic or Manual (safe start)
  • Open Neutral Protection: Opens upon loss of neutral (applicable models only)
  • Grounded Neutral Protection: Trips if ground and neutral touch at load side (applicable models only)
  • Enclosure: NEMA 4X and 6P wet location rated; high impact withstand
  • Switch Interface: Double insulated
  • Latching mechanism: Electro-magnetic
  • Agency Approval: CSA, cCSA, cCSAus; CSA-C22.2 No. 144-M91 - UL 1053 (277 VAC non Listed)